Mirror Head Support - Original style. (one) GMC Motorhome

Ramco Mirror Gasket

SOLD IN PAIRS ONLY

For those of you who are, like me, concerned about the small details here is a gasket that is designed to fill the gap between the body and the Ramco mirror arms. This gap can also allow water to enter through the wiring hole unless properly sealed and is caused because the head of the caged retaining nuts are above the surface of the body by about 1/10th of an inch. This gasket is designed to go around these protruding heads and thus fill the gap. The hole in the center is for wiring to the mirror for those that have these options.

Sculpted aluminum Brackets replace existing steel brackets. Accepts GMC mirror heads

One kit does both left and right sides. ARMS NOT INCLUDED

Manual flat glass and manual convex glass. One kit does both left and right sides.

Kit includes mirror heads, arms machined to fit your GMC, wiring harness, control and instructions. This is an important modernizing update. This one change makes the whole RV look much newer.

(Remote flat glass and manual convex glass) One kit does both left and right sides.

Remote flat glass and manual convex glass-Heated.
Kit includes mirror heads, arms machined to fit your GMC, wiring harness, control and instructions. This is an important modernizing update. This one change makes the whole RV look much newer.

Remote flat glass and convex glass-Heated.

One kit does both left and right sides.

Multi Ceramic coating is heat repellant at its finest.
Roll or brush on the bottom of the fuel tank and engine hatch.
Recommended to prevent vapor lock.
Call for more information and instructions.

EXHAUST DOWN PIPE FOR STANDARD EXHAUST MANIFOLD. MUST INDICATE 455 OR 403. ALSO INDICATE PASSENGER OR DRIVER SIDE.

Exhaust Heat Shields for Fuel Tanks


Here is a kit of items to shield the heat from the exhaust pipe to the fuel tank.The factory installed these shields to help minimize problems of overheating the fuel and vaptor lock.
The 20 gauge steel heat shielas are power coated white to minimize the heater transfer to the tank through absorption and re-radiation.these shields are like the original heat shield swhich had 3/8" bend on both sides, but I extended the upper bend, which installs over the exhaust pipe to 2" to provide additional heat isolation to the fuel tank.

THIS IS A GM3 CALIPER BETTER KNOWN AS AN 80 MIL CALIPER. FOR THOSE WHO CHOOSE A MECHANICAL PARKING BRAKE FOR DISC BRAKE SET UP.THESE ARE THE LARGER CALIPERS THAN THOSE BEING USED BY OTHERS.

MUST ORDER 80 MIL HOSE AND BANJO BOLTS NOT INCLUDED. PLEASE NOTE GRIND DOWN SMALL CASTING MARKS BEFORE INSTALLATION

MUFFLER HEAT SHIELD WITH STRAPS GMC MOTORHOME

MUST ORDER 80 MIL HOSE AND BANJO BOLTS NOT INCLUDED. PLEASE NOTE GRIND DOWN SMALL CASTING MARKS BEFORE INSTALLATION.

The original exhaust manifold bolts lock system for some reason completely ignores the center bolt. We have developed a bolt lock system that applies to the manifold bolts in exactly the same manner at the originals but has the added feature of providing a locking function to the center bolt.We believe that the use of our 5-bolt lock will provide a significant improvement to the longevity of the exhaust manifold gasket.

The lock plates are CNC machined from 18 gauge galvanized sheet steel, sold as a pair to do both exhaust manifolds, and are shipped with a tips sheet providing installation suggestions.

Phase Two -WE USE LARGER CALIPERS FOR BETTER BRAKING POWER. TESTED AND PROVEN BETTER THAN OTHER SYSTEMS WITH SMALLER CALIPERS  Rear Brake Conversion for all  wheels has everything the phase one system has plus,P30 master cylinder, master cylinder bracket and disc/disc proportionate valve.

Designed SPECIFICALLY for the GMC MOTORHOME to produce Low End Torque. Comes with oxygen sensor ports.
Headers greatly reduce engine temperature by more efficiently drawing the exhaust gasses out. Lowering the temperature of the cylinder and the combustion chamber creates a denser fuel charge and therefor allows your engine to create more power.

Ceramic coating is a high luster silver color that will not discolor with the introduction of heat and is more resistant to corrosion and heat at even higher temperatures. It creates a thermal barrier which lowers the understood temperature and adds life to your headers. The approximate dimensions of the package is 36hx20wx16L

Phase One-Rear Brake Conversion Only. WE USE LARGER CALIPERS FOR BETTER BRAKING POWER. TESTED AND PROVEN BETTER THAN OTHER SYSTEMS WITH SMALLER CALIPERS
4 Rotors
1 Electronic line lock
4 80 Mill Calipers w. Pads
2 Sets Braided Stainless Steel Brake Lines
1 Parking Brake Line Valve
4 Caliper Mounting Brackets
2 Front brake hoses
Suggested Additional Parts to install at the same time: P35 Master Cylinder w. special bracket . HIGHLY RECOMMEND DISC/DISC PROPORTION VALVE $89.95 PACKAGE PRICE.MECHANICAL PARKING BRAKE ON THE REAR WHEEL ONLY IS AN OPTION.